Watts K-1 Polyethylene Icemaker Kit, 25-Feet

I got this kit to run a water line from my kitchen sink to my refrigerator's ice maker. I am not a plumber, but I do understand the basic concepts of plumbing and have tackled a few small plumbing jobs. The included instructions are not the best if you need to be walked through every little step, but if you have an experience level similar to me you should be able to get through it.

The kit I got had slightly different pieces than what is in the product picture, however it did have everything I needed. The picture shows 2 nuts and some washers to go on the bolts that hold the two pieces of the saddle together. In the kit I received there were no nuts or washers because the nuts are actually welded to the bottom part of the saddle and the bolts just screw directly into them. All other pieces were the same.

According to the instructions the self-tapping saddle valve that comes with this kit can only be used to tap into a supply line that is 3/8" to 1-3/8" plastic or copper so make sure and check the size and material of the line you will tap into if you plan on using this valve. My sink line is mostly the flexible stainless steel, but fortunately there was about a foot of copper pipe between that and the faucet which I was able to tap into. The one problem I had with this kit was with threading the saddle onto the tap-valve. If you look at the product picture it shows the T-valve already has half of the "saddle" on it, but mine came with that saddle part separate. You are suppose to be able to just screw that saddle on the tap-valve (it's already threaded so should not be an issue), however the hole in the saddle was slightly too small. I had to take a pair of vice-grips and and adjustable wrench and man-handle the thing on. After a good bit of elbow grease I was able to finally get it on, though, and after that installing the valve was very easy. After you tighten the saddle around the pipe (and put the included rubber gasket below the T-valve), you simply start turning the T-valve clockwise as far as it will go and there is a spike inside that pierces the supply line. It was so easy that I did not even feel it going into the pipe and actually thought at first it wasn't going down far enough to pierce it. When I turned the valve back the other way, though, water started flowing just like it should.

Then it was just a matter of running the plastic line to my fridge and using the included supplies to connect it. I used plumbers tape on all the threads just as a precaution, but supposedly you do not have to if you don't want to.

I would again caution anyone who wants a clear step-by-step guide from this kit, but I think as long as you have a basic understanding of plumbing you will be OK. I am giving it 4 stars due to the saddle valve issue and since the instructions could be better. For the price, though, I think this is hard to beat.

The local HD was charging a lot more for this same kit so I came here. This installed without a problem, saddle valve seems like it'll hold up. A common problem I've seen with the valves is they start leaking after they've been used (open/closed) a lot so only time will tell if the 7$ was worth it. It's about the same quality you would find from any kit in the sub 20$ price range. I prefer polyethylene over copper because it's easier to work with needing to move fridge in and away from wall primarily. You also wont have the copper taste with poly likewise I noticed no real plastic or unusual tastes with this. If you wanted to do it right you could probably get a better PEX line, or even go with braided/SS. But, it probably won't pay off I expect this to last the life of the fridge.

Buy Watts K-1 Polyethylene Icemaker Kit, 25-Feet Now

I got this on time but when I got everything hooked up it leaked at the refrigerator. Had to buy some extra fittings and then it still leaked. Come to find out that the tubing is not a true 1/4 inch so the fittings they sent in the kit let the water leak out. Went back to the store and bought more tubing and did it all over again and now it works. The only thing that did work was the saddle piece that you attach to the water supply. Would not recommend this to anybody.

Read Best Reviews of Watts K-1 Polyethylene Icemaker Kit, 25-Feet Here

I used this kit to install a water filter under the sink. While I didnt use all the items I used most of the kit. It is a good price for all that you get

Want Watts K-1 Polyethylene Icemaker Kit, 25-Feet Discount?

I would spend a little extra money and buy the pieces seperately. The hose is very low end. I would go braided stainless or copper and I would not use that hole puncture connection piece. I would just get a some kind of t valve. It is easy enough to figure out I am not very handy and with the homedepot guy and some common sense I figured it out and it the out come is mutch better than this kit.

Save 2% Off

Frigidaire Refrigerator Water Actuator Arm 241685703

• THIS FRIGIDAIRE 241685703 WATER ACTUATOR WORKS WITH MANY FRIGIDAIRE, ELECTROLUX AND KENMORE
• REFRIGERATORS
• Works with the following models: Frigidaire FLSC238DB4, Frigidaire FLSC238DS8
• Frigidaire FLSC238JS0, Frigidaire FLSC238JS1, Frigidaire FLSC238JS2, Frigidaire FRS6L9EFSS4

This is a substitute replacement for my Kenmore refrigerator actuator arm. Sears price was $87, but I got it from Amazon for $40. It fit perfectly and I received it in about three days from ordering. I dreaded installing it because it looked like I would have to tear into the water dispenser. My concern, what if I dismantled the dispenser, couldn't put it back together and then had to call Sears?! So, I gave it a try.

I removed the drip tray but there were no screws at the bottom of the module cover like the instructions indicated. I had to carefully pry out the bottom of the cover, then push down from the top and the cover popped off, no problem. One issue, the cover was still attached to the dispenser module by a ribbon cord. I couldn't figure out how to detach it so I left it on. The cover just dangled while unscrewed the three screws at the top of the module. I carefully wiggled out the module and pulled out the water tube. Then the module pulled out further so I could work on it.

I detached the red/black wire plug and had to cut it because it ran behind a little box. I unscrewed two small screws holding the broken actuator arm side prongs and then removed the broken arm. There was a spring arm that I had to make sure was in front of the actuator arm front prong. It allows the actuator arm to spring back so it's not constantly turning on the water. It was an easy thing to do.

Placing the water tube back in the water tube hole in the dispenser seemed impossible. I struggled with it for awhile then realized it would naturally go back into place as I screwed the module back on the refrigerator. It turned out to be simple once I realized the tube would just go back in place. I checked the water dispenser hole once I put in all the screws and I could see the tube was good to go.

The entire job was easy. It probably took me longer than most folks because I was very cautious and fooled around with the water tube way too long before figuring it out.

Easy job, saved me hundreds by doing it myself. To have a repairman come to the house would have been $100 just for the person to get to the house. Then if anything needed to be done, that would have been lots more.

Buy Frigidaire Refrigerator Water Actuator Arm 241685703 Now

This was an exact replica of the actuator arm I got quotes from Sears and other appliance stores nearby at more than double the amount. It did take me about an hr to figure out how to remove a few things around to install it but once I did, it felt good knowing I saved about $250 which is what some appliance techs wanted to charge me.

Read Best Reviews of Frigidaire Refrigerator Water Actuator Arm 241685703 Here

fits perfectly. found instructions for repair on youtube. it took about 20 minutes start to end to fix the dispenser

Want Frigidaire Refrigerator Water Actuator Arm 241685703 Discount?

Quick shipping and perfect fit. Unfortunately, the fridge install was a bit more complicated than initially thought but the part was perfect and everything works just fine.

This item is super tricky to install. I'm slightly above average when it comes to home improvements. Found a you tube video that make it pretty simple. Just a lot of steps and probably took me 1 hour from start to finish.

Amana 21.9 cu. ft. Bottom-Freezer Refrigerator, ABB2224WES, Stainless-Steel

• 21.9 Cu. Ft. Total Capacity
• ENERGY STAR Qualified
• Temp Assure Freshness Controls
• Two Humidity Controlled Garden Fresh Crisper Drawers
• Gallon Door Storage

Very happy with this refrigerator. We had only 30" of space, wanted the freezer on the bottom, and wanted black sides. Stainless ranges and microhoods are stainless and black, so why are so many appliance companies making stainless refrigerators with grey sides? Not a problem if the sides don't show, but a big problem if they do!

I do think it should come with one more door bin, which we just ended up ordering separately. It comes with the following storage pieces for inside of the door: 1 full-width bin, 3 half-width bins, and 1 half-width bin with a clear swivel cover. We ordered an additional half-width bin.

Buy Amana 21.9 cu. ft. Bottom-Freezer Refrigerator, ABB2224WES, Stainless-Steel Now

Had shopped around local retailers and viewed on line many makes and models. did a lot of research reviewing reviews. certain brands in some sizes had issues with a wide variety of problems. my goal was to find the best product at the best price. need a reversible door or one that swings from left to right. wanted a freezer drawer not door. the door type are roomier in the freezer compartment but not my idea of fun to sit on the floor and dig around in a pull out bin I found it a bit to awkward. a little disappointed that it did not come with an ice maker. but it was easy to install. unit is ice maker ready. had not really planed on getting the stainless steel model but it was not outrageous so I splurged the extra $100. very happy with purchase and glad I took the time to research.

Read Best Reviews of Amana 21.9 cu. ft. Bottom-Freezer Refrigerator, ABB2224WES, Stainless-Steel Here

I like this refrigerator a lot. However, if I had read about it more closely, I would have realized that it does not have an ice maker or a water filter. I ended up buying a separate ice maker which didn't cost a lot, but I had to pay a plumber to install it. The freezer isn't that big, but it works for us. And, the only other complaint I have is that the refrigerator really needs an additional door compartment (there is space, but not enough compartments).

Want Amana 21.9 cu. ft. Bottom-Freezer Refrigerator, ABB2224WES, Stainless-Steel Discount?

Same review as posted for white fridge:

I had an Amana for over 20 years with no problems but it was very rusty and dirty so I decided

to replace. The plastic piece between the bins broke and the replacement went also.

In little under 2 years I went to unplug to clean underneath and behind the fridge and the thermostat went immediately.

Between waiting for the repair guy and now a replacement part it is going on two weeks and I have had to discard

food. I would recommend unplugging the refrigerator while the warranty is

in effect to see if you too see a correlation between that

and the demise of the thermostat! I have been led to believe that appliances do

not last long (under 5 years?) due to the computerized energy-efficient "gadgets" that are now used.

I think there is also built-in obsolescence. Good luck with your appliances.

Just to add: The freezer bottom fills with water as the water is not draining properly (drain-pipe iced?)

and then the water freezes and eventually starts to flow over onto my kitchen floor. From what I have researched I can

defrost or use a hairdryer on the drain or pour hot water down. I chop away at the ice periodically.

What a nightmare this fridge is.

Save 14% Off

Beware of lack of replacement parts. Amana stops making replacement parts 5 years after the model comes out. Parts (shelves, drawers, etc) are impossible to obtain, thus making large sections of the refrigerator obsolete before its time. Would never buy another Amana product.

WC-20TL: ThermoElectric with Touch-Sensitive Controls (20-Bottles) # WC-20TL

• 20 standard bottles / 48L capacity
• Reflective glass door with touch sensitive controls
• Adjustable thermostat with LED temperature display
• Quiet operation (30dBA)
• No vibration (bottle sediment is not disturbed)

I have had my Sunpentown 20 for a week now and I like it. Most bottles I have fit except for one of the fatter reds that I have. The shelves slide out and the light is a nice touch. It emits a very low hum. It sits next to my computer and I really don't notice it unless the house is very quiet. The touch control is not overly sensitive and its max low end temp is 54. I plan to regularly clean the exhaust and intake vents since I suspect dirt in them killed my last wine fridge which was NOT a Sunpentown.

Whirlpool 8212547RP 5-Feet Pex Ice Maker Hook-up Kit

This product works exactly as expected. Installed in less than 5 minutes. I originally bought a kit at the hardware store that was going to have to be cut to size, etc, but this was just plug and play. Would highly recommend.

This is one of those little pieces of hardware that exactly fits the job. Installation was simple, and no leaks or any problems to speak of.

Our fridge has an ice maker, but we didn't like the chlorine taste (the fridge doesn't have a built-in filter) and so we got an external inline water filter. This hose runs from the water hookup to the filter, which then connects to the water input on the fridge through the hose that came with the fridge.

Buy Whirlpool 8212547RP 5-Feet Pex Ice Maker Hook-up Kit Now

This product works flawlessly and was easy to install. Would recommend to anyone needing a hook up kit 5 feet or less.

Read Best Reviews of Whirlpool 8212547RP 5-Feet Pex Ice Maker Hook-up Kit Here

This was the perfect item to make the ice maker install a snap; not just convenient, but quick and easy.

Want Whirlpool 8212547RP 5-Feet Pex Ice Maker Hook-up Kit Discount?

Not much to say except that it does the job as described and is a good quality product. I would recommend this to anyone wanting to add a filtered water line to their sink or ice maker.

EdgeStar Deluxe Mini Kegerator & Draft Beer Dispenser

• AC and DC compatible with DC adaptor cord included for easy portability
• Temperature Range: 38-54 degrees Fahrenheit
• Accepts Heineken 5 liter Draughtkegs
• Capacity: 1 standard 5L mini keg
• Dimensions: 15inches h x 15inches w x 13inches d

The Background:

I first thought of the BeerTender from Heineken as the 5L kegs are simple, easy to use and a big hit at parties and keeping the beer cool and out of the fridge is a challenge. While in a specialty shop I saw several other foreign brands of beer also in 5L kegs, but to my surprise, their tap was at the bottom like a Gatorade cooler. I then learned that the Heineken Draft kegs have an internal pressure system and that the Beertender would only work with that particular type of keg.

The Search:

At first it didn't really matter that much to me because I love Heineken and Heineken Light. After seeing the variety of beers available in the 5L minikegs, I decided to start shopping for a kegerator that would work with more than just the Draftkeg line. A low price was important, but so was functionality and reliablility. While searching, I found several other options with most looking similar and having the same features. You can go crazy and get one of the $300+ models out there, but I'd only recommend doing that if you have that kind of cash-flow to spend on a counter-top beer dispenser.

The Product:

The EdgeStar Mini Kegerator jumped out at me first because of its low price, and second, because it's identical to the more expensive Avanti MBD5L Mini Kegerator. (Note: Although the Edgestar doesn't display a drip tray like the Avanti, one is included.) For about $50, you can purchase a CO2 kit to tap and use non-pressurized 5L kegs from any other brewer (I've even seen it suggested that home-made beer can be placed in such a keg.) The kit comes with three 16-Gram CO2 cartridges (the small silver ones that you can pick up at Walmart) which are enough to dispense 3 or more 5L kegs. If you don't feel like replacing the cartridge every time you change the keg out, the space provided for the CO2 canister is large enough to accommodate a larger (340-Gram) CO2 Cylinder which is enough to dispense up to 20 5L kegs! The EdgeStar comes with a direction booklet, a cleaner bottle to wash out the system, an AC cable and DC cable, and an adapter for the Heineken Draft kegs.

The Perks:

Having draft beer right in your own home!

Looks great and comes in silver or black

Better than the BeerTender for the following reasons:

o Costs less even with the CO2 kit

o CO2 kit allows you to use any 5L keg

o Has a controllable temp fan (38-54 degrees Fahrenheit) for a variety of beer types

o Comes with a DC adapter for tailgate parties and RV use!

The Bad:

Can be tricky for people who don't normally pour from a tap

Pours a lot of head if not setup properly (I suggest coiling the tube and getting it as horizontal as possible to mitigate this.)

Tap is plastic, not stainless steel

Five stars because even with the few shortfalls, it blows the BeerTender away!

Buy EdgeStar Deluxe Mini Kegerator & Draft Beer Dispenser Now

As I'm sure with many people looking for a 5 liter keg unit I was torn between the various ones out there and the Krupps BeerTender. I chose the Edgestar due to the low price, looks and the additional ability to utilise a CO2 cannister, which the BeerTender cannot. As far as I know the Heineken 5L keg is the only keg to come with its own CO2 built-in and only such kegs are usable with the Krupps model. Therefore, whilst I'm a Heineken fan, the BeerTender completely limits your choice of drinkto Heineken or Heineken Light.

So I bought the Edgestar, sight unseen and I'm very glad I did. It's a light-weight unit comprising mostly of chrome plastic and a few actual chrome parts, and overall looks great and feel sturdy. The drip tray (not shown in the picture but supplied) is well thought out and easy to remove when full. The door is opened by a small button on top and swings outward. You only have to open it a short amount to place a keg in it, offering a small footprint for the unit. The keg is cooled by a plate and you have a blue backlit display indicating current temperature which is adjustable using the chrome buttons. There is also a small blue led inside the cabinet which is nice although not bright it can be toggled on and off using the lower button on the front of the display.

The tap is solid. I was completely surprised by how firm it is and it works a treat. The small black beer tap is removable and so you could replace it with one of your own if you had the right sized thread.

The unit is supplied with an AC and a DC lead so you could power it from a car/RV/boat. It also comes by default with a Heineken keg connector which was supremely easy to attach.

A final sweetner is the ability to clean the lines, which the BeerTender amazingly does not have (you have to buy a new line for each and every keg you use with the Krupps). The Edgestar comes with a small plastic bottle which I filled with 2 parts water and 1 vinegar and it clips onto the line and you simply squeeze it as you open the tap. Took 20 seconds.

Now I haven't purchased the optional CO2 kit yet, choosing initially to use up my Heineken kegs, but I have no fear that the kit will work as advertised. The small black circle to the right of the tap that you see in the picture is for a CO2 gauge to fit into, and the CO2 bottle sits inside the unit so it's all tucked away neatly.

Ultimately, very happy with the unit and had my first pint last night.

Cheers!

Read Best Reviews of EdgeStar Deluxe Mini Kegerator & Draft Beer Dispenser Here

I originally wrote this review for what I think is a different model of kegerator by this same company. After reviewing both listings, this is clearly the model I own, but the other model doesn't contain enough information on the Amazon page for me to tell if it's a duplicate of this one, or another model entirely. I lean towards the former. Off we go...

The reason I chose this kegerator is because the vast majority of kegerators on the market 1) only take Newcastle or Heineken pre-pressurized mini kegs, or 2) are really expensive. I'm not a huge macrobrew fan, so the fact that this model will accomodate non-pressurized 5-liter kegs is a huge plus. It's essentially the only reason I wanted it.

Now, if you're going to use the pre-pressurized kegs, it's a very easy process with only a few steps to get set up. If you're using non-pressurized kegs, it's a little more involved.

General Principles:

-CHILL YOUR KEG. If you don't chill your keg for at least 12 hours, you will get warm, gross, flat beer.

-Read the instructions. Especially when dealing with non-pressurized kegs.

-If you want to use this with non-pressurized kegs, you MUST buy the C02 adaptor kit. I've read some reviews indicating they were very hard to find. My wife got one with no issues.

-When using the C02 kit with non-pressurized kegs, ensure that 1) you keep the beer-to-tap supply line as straight and level as possible, and 2) keep the pressure valve set so that the C02 flow is extremely low-to-nonexistent for the first few pours, otherwise the first pints will be nearly all foam; increase the pressure in increments with each additional pint to maintain a proper head on your beer.

-Be sure to buy food-grade C02 cylinders, not sporting (paintball, bb etc). Sporting C02 often contains oil.

Upsides:

-Variable temperature settings.

-Compatible with all 5-liter kegs (with adaptor).

-Draft beer in your home. Can you beat that? No. No you can't.

-Once it's set up, it's easy to use and clean. No need to purchase new lines after each keg (as in the Krups Beer Tender); just use the included cleaning kit, water, and a little vinegar.

-With the adaptor, use any available 5-liter keg.

-If you homebrew, you can find brand-new, empty 5-liter kegs on Amazon. You can keg-condition 5-liters of your own beer and dispense it as a draft in your own home. How cool is that?

Downsides:

-It's not heavy metal construction, so you'll need to be a little gentle, especially until you get a feel for the tap. Don't yank that thing, be kind!

-Instruction manual is not terribly user-friendly. Take your time to study it, especially when using the C02 adapter kit. They could have done a much better job with the pictures and step-by-steps. Of course, it may help if you refrain from drinking while you're setting it up.

-When using the C02 adaptor: If you're obsessed with a perfect pour of beer, you'll need some practice with the C02 settings to make sure your foam-to-beer ratio is right.

Another thing worth noting, which I don't consider a downside, is that there aren't currently a ton of mini-kegs available. Other than the pre-pressurized Newcastle and Heineken, most everything else I've seen are German beers (Hefeweizen, Kolsch, Dortmunder, Pilsner, Maibock, Schwarzbier, Rauchbier, Kellerbier) in limited variety. Fortunately, most these are from good breweries (Einbecker, Reischdorff, Kulmbacher, Kostritzer, etc) and I like those styles of beer. However, you're not really going to find much in the way of American beers on here, especially if you like microbrews. Coors Light I understand is test marketing a 5-liter keg. HOWEVER, if you are a fan of Bell's Oberon summer beer (and who isn't), they DO offer 5-liter kegs of it. Oh frabjous day!

Want EdgeStar Deluxe Mini Kegerator & Draft Beer Dispenser Discount?

For a while now I've wanted a kegerator for the bar/theater, but I've lacked the space for a full(or even mid-) sized one. So today, despite some iffy reviews here and there, I bought an Edgestar mini-kegerator to sit on top of the mini-fridge in my bar.

This little machine keeps a 5L beer keg chilled at 38 degrees and delivers the perfect amount of head for a pint glass...only you get used to the pour speed and nozzle strength. The unit is pretty much like the Krups BeerTender machines that support Heineken and Newcastle, but this one also supports non-pressurized mini-kegs. I have to admit that I'm not a beer expert by any means, but when I heard that Newcastle was FINALLY available in Atlanta in the 5L size, I jumped all over this.

After a short 4 hours with the unit, I'm breathing a sigh of relief (between beer pours, that is). As I mentioned above, reviews have been hit or miss. Some people complained the non-pressurized conversion kits weren't yet available. Maybe I'm just lucky, but I had no problem ordering the Edgestar-branded one two days ago, and it even arrived before the main unit itself. Some others complained Heineken was the only act in town. My local stores have all kinds of non-pressurized beers, in addition to the Heineken and Newcastle kegs, so again I'm probably just lucky to live in a fairly large city. Some folks said the unit was just cheap plastic junk. That last point will probably be true for me at some point, as the unit is just plastic and faux chrome, but at $140 I couldn't have expected too much more. Someone somewhere said that the door was constantly ajar and the cooling plate couldn't do its job. From what I've heard and now seen firsthand, this just isn't a problem. My mini-kegs set nicely on the cooling plate inside the unit and I'm able to close the door completely and securely.

My only complaints so far are 1) the internal fan or whatever parts make it go are a bit louder than I'd like, and 2) I dislodged a washer in the plastic cleaning solution bottle that came with it. The second part was just stupidity on my part when I first flushed the lines, and it's totally fixable, but the former point is indeed a minor inconvenience. It's no louder than my ice maker or mini-fridge, but it's something else whirring in the back of the theater. Oh well.

So at this point, my margarita machine quest is on the back-burner indefinitely as I work on my beer pour perfection and fish out that stupid washer in the cleaning bottle. But for anyone in my shoes who may be considering one of these units but afraid of the spotty older reviews of the unit, I'm pretty pleased so far.

Cheers.

Save 57% Off

I bought this so I could enjoy some of our Seattle area microbrews which aren't available bottled.

My first one died after 1 1/2 weeks. The unit ran constantly but the cooling pad no longer cooled. I contacted warranty service and sent it back. They said the warehouse was busy, so it took about two weeks to get a replacement. The second one is working fine after three weeks.

I bought it with the optional conversion kit for non-pressurized kegs, because I buy my beer in growlers and transfer it to a mini keg. The regulator is also a bit finicky. I've found the pressure can suddenly rise 2-4 PSI several hours after you've set it, so I now set it a little below where I want it and work up to the pressure I want over a day or two. My digital thermometer tells me the actual temperature of the beer right after I pour it is 5-6 degrees higher than what i have it set to. I like my beer in the '30's and it isn't able to chill it below the low 40's. A pre-chilled (frozen) glass helps, and with the pressure set at 12-13 PSI, I like the results I get with my favorite IPA's.

There is a review saying that the plastic tap broke when disconnecting it from the keg. The tab fits very tightly into the rubber bung, to prevent gas leaks. The instructions say to wet the probe before sliding it in. When a keg has gone dry, the probe is dry plastic against dry rubber. I've found turning the keg upside down and sloshing it around a bit, and then turning it right side up, filling the top recess with water, turning the tap clockwise a few turns, pushing down a bit and trying to get some lubrication between the probe and the bung allows removing it without breaking things. Also a fussy operation.

All in all, after five mini kegs, I'm happy with it. There aren't many competitors, so if they up-graded the quality a little and charged a bit more, I would still buy one.

Frigidaire 240338001 - FRIGIDAIRE REFRIGERATOR DOOR BIN - UPPER

• THIS 240338001 FRIGIDAIRE DOOR BIN IS DESIGNED TO HELP YOU ORGANIZE AND KEEP TRACK OF THE FOOD

• IN YOUR REFRIGERATOR. MANY BINS HAVE SEPARATE TEMPERATURE CONTROLS AND CAN EITHER BE OPAQUE OR
• CLEAR. SOME ARE DESIGNATED FOR SPECIFIC STORAGE ITEMS, SUCH AS MEAT OR VEGETABLES.

• Works with the following models: Frigidaire 30-2251-00-01, Frigidaire 30-2251-23-01
• Frigidaire 57-2707-10-01, Frigidaire 57-2707-10-02, Frigidaire 57-6707-10-01

This item is exactly what I needed. It fit perfectly, and was delivered in a timely manner. I am so happy to have my refrigerator back in one piece.

Buy Frigidaire 240338001 - FRIGIDAIRE REFRIGERATOR DOOR BIN - UPPER Now

it fit the door well, it went in place in 10 seconds, the only negative was I thought the price was a tad high for plastic, but this is the world we live in.

Read Best Reviews of Frigidaire 240338001 - FRIGIDAIRE REFRIGERATOR DOOR BIN - UPPER Here

My door bin broke and this replacement door bin was just what I needed. Fits perfectly. Received the door bin promptly would order again if needed

Want Frigidaire 240338001 - FRIGIDAIRE REFRIGERATOR DOOR BIN - UPPER Discount?

fits perfectly, price was nice and it was shipped immediately!!! what more could you want! could not be happier to fix frig and save money.

This door bin was a perfect replacement part for my refigerator. To be sure it was the right one I called Frigidaire with my refigerator serial number before I ordered this door bin. I tried finding it on my own first and wasted time. Better to just be sure. The replacement arrived quickly and was a perfect fit!! Was also reasonably priced.

Whirlpool Refrigerator Icemaker Ice Maker & Water Valve 2206123

• VALVE, SOLENOID
• Works with the following models: Whirlpool CS22AEXHN00, Whirlpool CS22AEXHN01
• Whirlpool CS22AEXHN02, Whirlpool CS22AEXHW00, Whirlpool CS22AEXHW01, Whirlpool CS22AEXHW02

I *try* and do as many DIY projects that I can and after replacing my actual ice maker, water still wasn't being sent up through the tubes I figured that I needed a new valve. I found this valve on Amazon great deal on price and the seller had good reviews. The seller is wonderful, shipping was extremely fast and packaging was ideal. The installation was incredibly easy just take out the old and hook up the new. I was hoping this new part would solve my problems and so I anxiously watched/listened for the pump sound and sure enough...water was shooting down the ice maker tube and now my ice maker runuth over!!!!!

Buy Whirlpool Refrigerator Icemaker Ice Maker & Water Valve 2206123 Now

Once I called customer service a clarified the connectors were the newer quick connect type, everything went together great. Customer service was very helpful since the unit I was replacing had screw on fittings.

Read Best Reviews of Whirlpool Refrigerator Icemaker Ice Maker & Water Valve 2206123 Here

The valve was easy to install. It sure beat the service fees of a appliance center. This company was great to do business with.

Want Whirlpool Refrigerator Icemaker Ice Maker & Water Valve 2206123 Discount?

I ordered this a little more than a week ago, and I already have a tray full of ice!! With no water leaks! Seller ships quick, and it was a breeze to install. Absolutley recommend buying from this seller. Thanks!